Land Pride RCM6615

New Products / Land Pride / Rotary Cutters / RC6615 Rotary Cutters / RCM6615

Double tap to zoom

Features
Specifications

Features

Features	Benefits
Surpassed rugged industry standards	All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.
Factory assembled	Saves customer set-up time and money.
7 Year gearbox warranty*	Shows confidence in gearbox integrity. (Years 6 & 7, parts only.)
Rugged heavy built gearboxes	Capable of handling heavy cutting applications.
Gearbox Seal Protection	Gearbox bottom seal protection for longer bearing life.
2 3/8" Output gearbox shaft	Large output shaft handles shock loads better.
Input driveline: Cat. 6 CV or Cat. 5 Conventional	Holds up to shock loads and harsh mowing conditions.
Cat. 5 intermediate & Cat. 4 wing drivelines with slip-clutches	Driveline is sized right for the intended cutting capacity. Slip-clutch will slip under load instead of twisting the driveline.
Rugged heavy built gearboxes	Capable of handling heavy cutting applications.
Gearbox Seal Protection	Gearbox bottom seal protection for longer bearing life.
2 3/8" Output gearbox shaft	Large output shaft handles shock loads better.
2 Piece shield on wing gearboxes	Driveline grease zerks are easier to access.
Self-leveling hitch	Reduces drawbar wear by keeping hitch level while going through ditches. All drivelines have access holes for greasing the U-joints and inner profiles.
Hinged wing sections	Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.
1" Solid hinge rods	Larger diameter hing
Wing transport lock pins	Holds transport wings in the folded-up position in case of hydraulic pressure loss.
Enclosed front to rear dual leveling rods	Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod.
5-Bolt hubs	5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Drain holes in wheel rims	Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.
Spring-cushioned trailing arms	Provides independent suspension, cushions loads on drawbar.
Replaceable wheel spindles	Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove one bolt to replace damaged spindle.
Pre-cut chamber	Allows grass and vegetation to stand back up prior to cutting for a more complete cut.
Reinforced leading edge	Front of deck can withstand heavy brush and saplings.
Collapsible leveling rods	Prevents damage and failure to leveling rods.
1" Leveling rods	Large diameter leveling rods provide superior supporting strength over rough terrain.
Double swivel hitch option	Great for uneven terrain, reduces drawbar wear.
Bar-tite hitch option	Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.


Grease zerks on end caps of driveline cross journals	Intermediate and wing driveline cross journals are easier to grease.
High blade tip speed	Allows clean cutting of material and even distribution.
6" Blade overlap	Eliminates skipping during turns.
High cutting capacity 56 Series 66 Series	Can cut brushy areas with saplings up to 4". Can cut brushy areas with saplings up to 4 1/2".
Pre-cut chamber	Allows grass and vegetation to stand back up prior to cutting for a more complete cut.
Reinforced leading deck edges	Front of deck can withstand heavy brush and saplings.
12" Deck height	Handles heavy cutting, which reduces balling-up of cut material under the deck.
10 gauge smooth deck top	Reduces accumulation of debris and is easier and faster to clean.
7 Gauge smooth deck bottom	Heavy deck design holds up to harsh conditions. No bottom obstructions.
Replaceable 1/4" side skirt	Reduces debris piercing possibilities. Can be replaced if damaged.
Left wing rotates clockwise	Better discharge of material. Picks up tractor tracks.
3/16" Stump jumper backed with a 1" thick mounting bar	Heavy round stump jumper. Can hold up to tough conditions
Beveled skid shoes on wings	Reduces gouging the ground when turning.
LED Signal lights	LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts.
Hinged wing sections	Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.
Greasable wing folding hinges	Provides for a long hinge life and allows wings to fold up and down with less stress.
1" Solid hinge rods	Gives greater strength to the cutter from front to rear, and in the hinge area itself.
Wing transport locks	Holds transport wings in the folded-up position in case of hydraulic pressure loss.
Collapsible 1" leveling rods	Prevents damage and failure to leveling rods. Large diameter leveling rods provide superior supporting strength over rough terrain.
Enclosed dual leveling rods	Cutter pulls equally on the rear axle while traveling over rough terrain.
5-Bolt hubs on trailing arms	5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Drain holes in wheel rims	Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.
Spring-cushioned trailing arms	Provides independent suspension, cushions loads on drawbar.
Replaceable wheel spindles	Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove one bolt to replace damaged spindle.
Wheel options	Laminated tires: Eliminates flats. Airplane tires without foam filling: Give better cushion while transporting. Airplane tires with foam filling: Give better cushion while transporting and can’t go flat.
LP Performance hitch option	Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar.
Bar-tite hitch option	Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
Roadway light kit option	Allows operator to transport on public roads safer when head lights are turned on and/or when flasher lights are turned on.
Deck rings (optional)	1/2" x 3" full welded deck ring keeps blades from damaging the deck.

Specifications

Model Number	RCM6615
Horsepower Range	50 to 250 hp (37.3 to 186.4 kw)
Gearbox Horsepower	250 hp (186.4 kw) Splitter 210 hp (156.6 kw) Center & Wing (Blade spindle gearboxes are built heavier)
Gearbox Lubrication	Gear Lube 80-90W EP
Gearbox Oil Capacity	5.5 Pints (2.60 L): Divider gearbox 10 Pints (4.73 L): Center deck, LH deck & RH deck spindle gearboxes
Cutting Capacity	4 1/2" (11.4 cm)
Tongue Weight	1,860 lbs (843.7 kg)
Machine Weight	Single row chain guards, 6 aircraft wheels, 540 CV main driveline & standard clevis hitch 5,660 lbs (2567.3 kg)
Blade Tip Speed AT 540 rpm AT 1000 rpm	Center blades = 16,300 FPM (82.8 mps) Wing blades = 16,300 FPM (82.8 mps) Center blades = 16,300 FPM (82.8 mps) Wing blades = 16,000 FPM (81.3 mps)
Hitch Types	Optional Self-Leveling Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Pintle Hitch, or Ball Hitch
Hitch Jack	Standard (7,000 lbs)(3175.1 kg)
Signal lights 7 Pin connector	LED SAE J560 pin configuration
Cutting width Overall width Normal transport width Minimum transport width	15' - 0" (4.57 m) 15' - 11 3/4" (4.87 m) 9'-1" (2.77 m) 7'-6" (2.29 m) With transport locks & deflectors removed and cylinders fully retracted
Overall Length	16' - 0" (4.88 m)
Deck Height	12" (30.5 cm)
Cutting Height	2" to 14" (5.1 cm to 35.6 cm)
Lift Hydraulics	3 1/2" Bore x 8" stroke hydraulic cylinder, hoses, fittings & stroke control spacers
Wing Hydraulics	3" Bore x 8" stroke hydraulic cylinders, hoses & fittings
Wing Transport Protection	Wing transport lock pins
Deck Material	10 gauge (3.4 mm) top deck and 7 gauge (4.6 mm) bottom deck
Side Skirt Material	Bolt-on replaceable 1/4" (6 mm) steel
Skid Shoes Wing deck Center deck	Reversible & replaceable: 2 straight skid shoes and 2 AR400 leading skid shoes. Replaceable: 2 skid shoes
Blades - 4 (2 per Carrier)	1/2" x 4" (1.3 cm x 10.2 cm) Heat treated free swinging alloy steel with up lift
Blade Overlap	6" (15.2 cm)
Blade Bolt	Keyed with hardened flat washer & locknut
Stump Jumper / Blade Holder	3/16" (5 mm) Thick round dish-shaped pan, reinforced with 1" x 5" (2.5 cm x 12.7 cm) blade bar; or optional shredder kit
Deck Ring	Optional 1/2" x 3" (1.3 cm x 7.6 cm) fully welded
Front & Rear Guards	Optional rubber, single chain, double chain, or double chain with cable
Input Driveline 540 & 1000 rpm	Cat. 6 with constant velocity u-joint or Cat. 5 with conventional (non-cv) u-joint
Intermediate Driveline	Category 5 star profile with slip-clutch
Wing Driveline	Category 5 star profile with slip-clutch
Tire Options	6" x 21" Laminated tires, 25.5" new tire with or without foam fill, 29" x 16 ply used aircraft tires without foam filling.
Number of Wheels	6 - Wheel option: 4 on transport axle and one on each wing axle 8 - Wheel option: 4 on transport axle and two on each wing axle
Transport Axle	Spring-cushioned on trailing arms
Hubs	Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts