New Holland Discbine® 209

Double tap to zoom

 

Features

FAST, SMOOTH CUTTING

The maneuverable 9’2” Discbine® 209 and the 10’4” Disbine® 210 make high-quality hay with the smooth, trouble-free performance you expect from a genuine Discbine.

MOWMAX™ DISC CUTTERBAR 3-YEAR FACTORY WARRANTY

New Holland’s MowMax™ disc cutterbar breezes through tough mowing conditions and is backed by three full years of factory warranty so you can cut close with confidence.

QUICKMAX™ BLADE CHANGE SYSTEM IS STANDARD EQUIPMENT

The QuickMax™ knife change system makes it easy to keep knives sharp for the close, clean cut you want and increased tonnage.

HIGH QUALITY AND FAST DRYDOWN

Choose the best conditioning system for your crops – rubber chevron rolls, steel chevron rolls or advanced LeaningEdge™ flail tines.

Specifications

Discbine® 209  
Cutterbar  
Cutting width ft. in. (m) 9' 2" (2.8)
Cutterbar model MowMax™ Modular Cutterbar with ShockPRO™ hubs
Number of discs 7
Knives per disc 2
Disc speed @ 540 rpm PTO speed rpm 3000
Tilt angle degrees 2° - 10°
Flotation Up & back, adjustable springs
Drive method PTO drive with slip & overrunning clutch to bevel gearbox to LH end of header, vertical PTO shaft to cutterbar
Cutting height in. (mm) 1.1-2.7 (29-68)
Cutting height w/optional high-stubble shoes in. (mm) 2.25-4.5 (58-115)
Cutting height w/optional adjustable shoes in. (mm) 2.25-4.5 (58-115)
Roll Conditioners  
Type Chevron intermeshing rubber
Length / Diameter in. (mm) 90 (2286) / 10.4 (264)
Drive method 4 HB V-belt and enclosed gears
Speed rpm 647
Conditioner roll tension adjustment Single crank
Conditioner gap adjustment Adjustable drawbolt stop, each end
LeaningEdge Flail Conditioners  
Type Flail rotor with 90 tapered flails
Length / Diameter in. (mm) 90 (2286) / 22 (560)
Drive method 4 HB v-belt
Speed rpm 718 std. 1000 opt.
Conditioner gap adjustment Single crank adjustable rotor hood
Crop Discharge  
Swath width ft. (m) 6 (1.83)
Windrow width ft. (m) 3-6 (0.9-1.83)
Driveline  
Input speed rpm 540
Driveline protection Slip clutch and overrunning clutch assembly at rear of PTO shaft
Secondary driveline Non-CV driveline
Tongue Options  
Type Side-pull, straight tongue
Hitch type Drawbar with CV PTO
Tractor Requirements  
Minimum PTO power required hp (kW) 65 (49)
Hydraulic circuits required 2
Minimum relief pressure required psi (bar) 1500 (103)
Drawbar ASAE Category II
Swivel Hitch - Drawbar
Swivel Hitch - 2-Point
Electrical 7-pin electrical connector for transport lights
Tires  
Tubeless ag rib implement tires 9.5L x 14L 6PR
Transport Speed  
Max road speed mph (kph) 20 (32)
Dimensions*  
Width, transport ft. in. (m) 9' 11" (3.02)
Width , operating ft. in. (m) 14' 10" (4.52)
Length, transport ft. in. (m) Flail Tine: 18' 1'' (5.50)*** or Roll: 17' 7'' (5.23)***
Length, operating ft. in. (m) Flail Tine: 17' 8'' (5.4)*** or Roll: 17' 2'' (5.23)***
Height ft. in. (m) Transport: 5' 8" (1.73) / Operating: 4' 5" (1.35)
Ground clearance with head fully raised in. (mm) 17 (4.32)
Weights**  
Operating weight lbs. (kg.) Flail Tine: 3690 (1674)*** / Roll: 3740 (1697)***

— Not Available
*** Rear curtain down for all height and length measurements on machines with flail conditioners. Subtract 2” (50.8 mm) for flail curtain up. Windrow shields fully open for length in both positions.
*** Weights with rubber conditioning rolls. Add 100 lbs. (45 kg) for steel rolls.
*** Weights & dimensions are with standard drawbar hitch. Add 150 lbs. (68 kg) & 2 ft. (.60) length for swivel hitch models.